The fully hydraulic steering system has many advantages such as easy and flexible operation, simple structure, low price, and convenient installation and layout of the whole machine. Currently, most of the steering systems on medium and high horsepower tractors use fully hydraulic steering systems, and mechanical steering is difficult to see. The fully hydraulic steering system is usually used on non road wheeled mobile vehicles with a speed of no more than 60 kilometers per hour. The fully hydraulic steering system on tractors mainly consists of three components: the fully hydraulic steering gear, the constant flow relief pump, and the steering cylinder.
In the use of tractors, steering sinker is a common fault, which has various manifestations. Below, we will analyze the manifestations, causes, and solutions of steering sinker faults as follows:
1. Heavy steering (heavy when turning left or right), unable to turn the steering wheel
The common causes of this type of malfunction are as follows:
1.1 The oil in the steering oil tank is insufficient and needs to be refilled to the specified level. At the same time, check for any leakage in the hydraulic steering components, pipelines, and joints. If there is any leakage, it should be dealt with in a timely manner;
1.2 The constant flow relief valve on the constant flow relief pump has serious internal leakage. The leakage of the constant flow relief valve is caused by the wear and loose sealing of the constant flow valve core, which needs to be replaced; The constant flow overflow valve core is blocked by dirt in the oil, resulting in poor sealing. The constant flow valve core needs to be cleaned; The set pressure of the constant flow valve core is too low, and it is necessary to readjust the pressure of the constant flow valve core. The magnitude of the set pressure of the constant flow valve core is adjusted by the fastening screw or adjusting gasket. When the fastening screw is screwed in or the gasket thickness is reduced, the pre pressure of the spring increases, and the set pressure of the constant flow pump increases. Otherwise, it decreases. In actual maintenance, the constant flow overflow valve core is often blocked by dirt in the oil and the set pressure of the constant flow valve core is too low.
1.3 Wear of the gear pump on the constant flow overflow pump. Gear pump wear mainly manifests as wear between the tooth tip and the pump housing, as well as wear between the gear end face and the floating shaft sleeve. After wear, serious internal leakage will occur, causing a decrease in pressure and flow rate of the constant flow pump, resulting in heavy steering. At this time, it is generally necessary to replace the constant flow overflow pump.
1.4 If the steering fluid does not meet the requirements of the manual, such as high viscosity, it is necessary to replace it with steering fluid that meets the requirements of the manual.
The safety valve pressure of the 1.5 full hydraulic steering gear is low, and the safety valve opens too early, causing low pressure in the steering system and heavy steering. At this point, it is necessary to check whether the safety valve spring of the steering gear is deformed or failed. If the spring fails, it should be replaced. If the spring elasticity is insufficient, a shim can be added between the spring and the seat to increase the preload.
1.6 The steel ball of the power steering check valve in the fully hydraulic steering gear is missing, the check valve steel ball is blocked by dirt, causing it to seal poorly with the valve seat, and the check valve steel ball falls between the valve sleeve and the ring groove of the valve body, resulting in the one-way valve not closing tightly during power steering, connecting the inlet and outlet ports, and causing heavy steering. At this point, it is necessary to confirm the installation of the one-way valve, the sealing between the one-way valve ball and the valve seat, the cleanliness of the oil, and the cleaning of the steering gear.
1.7 The valve core and valve sleeve of the fully hydraulic steering gear are deformed and stuck. It is required to add a small amount of hydraulic oil to the inlet before installation. When rotating the valve core, it should be flexible and free. If there is any sticking, it should be ground or replaced.
1.8 Filter blockage and air in the oil circuit. If there is an oil filter in the hydraulic steering system, check whether the filter element is clogged. If the filter element is clogged, clean it thoroughly and replace the oil. If there is no filter element, check whether there is any foreign object blocking the inlet of the steering oil tank. If there is, remove the blockage, clean the oil tank, and replace the steering oil; If the oil in the oil pot is in the form of foam, it means that there is air in the oil circuit. The air inlet point should be carefully checked and the fault should be eliminated. When exhausting, the front axle should be set up or the steering link should be removed, the engine should be idling, and the steering wheel should be repeatedly turned from one end to another, so that the steering cylinder can exhaust air in the full stroke reciprocating motion.
The steering weight caused by mechanical faults such as stuck steering knuckles and poor lubrication of tractors should be lubricated or replaced in a timely manner.
2. Light when turning slowly, heavy when turning quickly
The common causes of this type of malfunction are:
2.1 Insufficient oil supply of constant flow overflow pump. The reasons for the insufficient oil supply of constant flow overflow pump are: firstly, poor sealing of the constant flow overflow valve core on the constant flow overflow pump to relieve pressure or low set pressure; secondly, wear of the gear pump on the constant flow overflow pump, which needs to be repaired or replaced.
2.2 The opening pressure of the steering gear safety valve is low and needs to be readjusted.
2.3 When air enters the steering oil, carefully investigate the location of the air intake and eliminate any air intake faults. At the same time, perform air exhaust operations on the steering oil circuit.
3. When the load is light, turn to light; when the load is heavy, turn to heavy.
The common causes of this malfunction are: 1. The opening pressure of the steering gear relief valve is lower than the working pressure of the steering system, and the opening pressure of the relief valve needs to be readjusted; 2. The overflow valve is blocked by dirt to relieve pressure and needs to be cleaned.
4. Turn with one side heavy and the other light
The common causes of this type of malfunction are: firstly, inconsistent steering resistance on both sides, such as flat tires on one side, etc. The reasons for the inconsistent steering resistance on both sides should be carefully checked and eliminated; The second is caused by the jamming and wear of the steering valve core and valve sleeve.
2026 November 2nd Week VAFEM Product Recommendation
Various of Clutch Release Bearings, more than 500 types different shapes, applying in the most of American, European, Korean, Janpanese, Asian car and truckes.
Each product develops according to the principles "Professional Design, Well Elaboration, Strict Regulations"
More than 50% of the output are OEM quality bearings.
VAFEM Clutch Release Bearings of buses & trucks have been already widely used for city buses and coaches, after improvements and technical innovations, has been proved to be consistency in high quality, steady warranty.
The Grease of Clutch Release Bearing is all used in imported high quality, high temperature resistant grease.
https://www.vafem.com/products/Hydraulic-Clutch-Bearings/912.html
2026-11-11